Volvo Penta DPI-A Cables & Fuses Mounting Bracket | 23370237

Part Number: 23370237
Supersedes: No confirmed supersession on record at time of listing
Replaced By: No confirmed replacement at time of listing
Brand: Volvo Penta
Official Product Type: Mounting Bracket Electrical / Cables & Fuses

The Volvo Penta 23370237 is a genuine OEM mounting bracket used in the DPI-A drive system, specifically referenced in the Cables and Fuses section of the Volvo Penta DPI-A parts catalog. It provides the factory mounting point for wiring and electrical components in that assembly, ensuring cables and fuses are secured in the correct position within the drive system.

Compatible Applications

• Volvo Penta DPI-A Cables and Fuses assembly (confirmed catalog reference)
• Additional DPI variants may apply verify against your drive serial number and the applicable Volvo Penta electrical diagram before ordering

Serial Number & Fitment Notice

Fitment can vary by drive model, electrical configuration, and production break. Always confirm part number 23370237 against your exact drive serial number and the applicable DPI-A cables and fuses diagram before ordering.

System & Diagram Position

System: DPI-A Cables and Fuses / Electrical Mounting
Diagram Position: Confirm exact position via the Volvo Penta DPI-A cables and fuses schematic for your serial-number range

Engine & Drive Family

Volvo Penta DPI-A pod drive. This bracket is part of the electrical / cables and fuses assembly rather than the engine itself.

When to Replace

• Bracket is bent, cracked, or distorted and can no longer hold components in the factory position
• Corrosion or damage to the mounting points or fastener holes
• Damage discovered during electrical service or cable routing work on the DPI-A assembly
• Any time the surrounding cables and fuses assembly is being fully serviced

Service Interval

Inspect during every electrical or drive service. Replace immediately if the bracket is damaged or no longer providing secure support for the wiring and components it mounts. Proactive replacement during a full DPI-A electrical overhaul is recommended.

Installation Notes

• Confirm the exact diagram position and serial-number fitment before installation
• Compare the new bracket to the original before fitting verify mounting hole pattern and dimensions match
• Inspect surrounding fasteners, wiring support points, and adjacent electrical components before reassembly
• Ensure all cable routing is restored to the factory position after the bracket is installed

Part Number & Supersession

OEM Part Number: 23370237
Supersedes: No confirmed supersession on record
Replaced By: No confirmed replacement number verify current status with Volvo Penta parts if ordering for a critical application

Dimensions & Weight

Approximate weight: 0.081 kg (0.18 lb). Bracket dimensions match the DPI-A cables and fuses assembly specification confirm fitment via the applicable schematic before ordering.

Kit Contents

Single mounting bracket (23370237). Fasteners and related hardware are separate line items.

Related Parts

• DPI-A cables and fuses assembly components confirm related part numbers via the Volvo Penta DPI-A electrical schematic for your serial-number range

Parts Desk Insights

Best use case: DPI-A electrical service or any time the cables and fuses assembly is being accessed. Replacing a damaged bracket at the same time as other electrical work avoids a return visit and ensures wiring is properly supported after reassembly.

Common customer issue: Small mounting brackets are easy to overlook during service, but an unsupported or incorrectly positioned cable can cause chafing and intermittent electrical faults down the line. Always match by serial number similar-looking brackets in the same assembly can have different hole patterns or mounting geometry.

Technical FAQ

Q: What does this bracket mount in the DPI-A assembly?
A: It is referenced in the Cables and Fuses section of the DPI-A parts catalog, where it provides the factory mounting point for wiring and electrical components. Confirm the exact position via the DPI-A schematic for your serial-number range.

Q: Can I use a generic bracket as a substitute?
A: Volvo Penta specifies OEM brackets for electrical assemblies. Mounting hole pattern, material, and geometry are application-specific substitution is not recommended where cable routing and support are safety-relevant.

Q: How do I confirm this is the right bracket for my drive?
A: Cross-reference part number 23370237 with your DPI-A drive serial number and the applicable Volvo Penta cables and fuses diagram. If you are unsure, pull the schematic for your serial-number range before ordering.